Case Communications 3200 Spezifikationen Seite 95
- Seite / 156
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
X723-300151 5-29 Issue 2
5.4.10 Cross-Connection configuration
The stream numbers on the cross-connect switch directly relate to the
PCM lines of Dual LIU cards as follows:
S1 Port 1 line 1 S3 Port 2 line 1
S2 Port 1 line 2 S4 Port 2 line 2 See section 1 Figure 1-1
Timeslots may be cross-connected between any stream, between any port
or between any stream and port without restriction e.g. P3 timeslot 8 to
S3 timeslot 27. The cross connection may be Simplex (unidirectional) or
Duplex (bi-directional). In Duplex it is only necessary to configure one
direction and the return path will be automatically assigned. The first
timeslot to be assigned may be selected to be TS0 to TS31 for all ports and
streams. If no first timeslot is selected, TS1 will be presumed.
Note that cross-connection of a timeslot to TS0 or TS16 of a Dual LIU (S1
to S4) can be made with no error message. Normally, the TS0 timeslot
data on the backplane will be overwritten by the framing in the PCM
stream. PCM TS0 NFW bits can be accessed via Dual LIU patchfields for
management purposes or routed via the DLIU TS0 routing options If the
line is in CAS mode the TS16 backplane timeslot data will also be
overwritten with the multiframing in the PCM stream.
Modify Format
The modification of the timeslot cross-connection is available with the
following format:
Example 1
(CCEMCC) Simplex | Duplex | Fixedata assign | Multipoint >D
output stream, start timeslot, end timeslot >S1
(S1; TS 1; Fixedata ;) from, TS, = ; >S2,1
(S1; TS 2; Fixedata ;) from, TS, = ; >S2,2
(S1; TS 3; Fixedata ;) from, TS, = ; >S2,3
In the above example the operator has only entered the output stream for
modification. The system then responds with the request for a source
stream and timeslot assignment starting at timeslot 1 of the output
stream selected i.e. S1. If the operator wanted to start at a particular
timeslot, including TS0, this could have been entered. The prompt for an
assignment would then start at the timeslot supplied as follows:
- 3200 Digital Multiplexer 1
- Operation Manual 1
- X723-3001510-2Issue 2 2
- STATUTORY NOTICES 2
- X723-300151 0-3 Issue 2 3
- X723-300151 0-4 Issue 2 4
- Contents 5
- X723-300151 0-6 Issue 2 6
- X723-300151 0-7 Issue 2 7
- X723-300151 0-8 Issue 2 8
- X723-300151 0-9 Issue 2 9
- X723-300151 0-10 Issue 2 10
- 1 Equipment Detail 11
- X723-300151 1-2 Issue 2 12
- X723-300151 1-3 Issue 2 13
- X723-300151 1-4 Issue 2 14
- A B C D E F 14
- A B C D E F 14
- 1.2 3200 Facilities 15
- 1.2.3.1 Configuration Fields 16
- 1.2.3.2 Equipment Map 16
- X723-300151 1-7 Issue 2 17
- 1.2.3.5 Alarm Event Options 18
- 1.2.3.7 Timeslot Assignment 19
- 1.2.3.8 Circuit Controls 19
- 1.2.3.9 Smart Configurations 19
- 1.2.3.10 Fixed Codes 19
- X723-300151 1-10 Issue 2 20
- * Incomin 21
- X723-300151 1-12 Issue 2 22
- 1.3 Mechanical Description 23
- X723-300151 1-14 Issue 2 24
- X723-300151 1-15 Issue 2 25
- 1.4 Specifications 26
- X723-300151 1-17 Issue 2 27
- X723-300151 1-18 Issue 2 28
- X723-300151 1-19 Issue 2 29
- X723-300151 1-20 Issue 2 30
- 1.5 Product Codes 31
- X723-300151 1-22 Issue 2 32
- 2 Installation and 33
- Commissioning 33
- X723-300151 2-2 Issue 2 34
- X723-300151 2-3 Issue 2 35
- 2.2 Installation 36
- X723-300151 2-5 Issue 2 37
- X723-300151 2-7 Issue 2 39
- X723-300151 2-9 Issue 2 41
- 2.3 Commissioning 43
- X723-300151 2-12 Issue 2 44
- X723-300151 2-13 Issue 2 45
- X723-300151 2-14 Issue 2 46
- X723-300151 2-15 Issue 2 47
- X723-300151 2-16 Issue 2 48
- X723-300151 2-17 Issue 2 49
- X723-300151 2-18 Issue 2 50
- 3 Dual Line Interface Unit 51
- X723-300151 3-3 Issue 2 53
- X723-300151 3-4 Issue 2 54
- 3.2 Dual LIU Adaptors 55
- X723-300151 3-6 Issue 2 56
- 4 Management Configuration 57
- X723-300151 4-2 Issue 2 58
- 4.3 Dual LIU Patchfield 59
- X723-300151 4-4 Issue 2 60
- X723-300151 4-5 Issue 2 61
- X723-300151 4-7 Issue 2 63
- X723-300151 4-8 Issue 2 64
- X723-300151 4-9 Issue 2 65
- Mux 1 Mux 2 Mux 3 66
- 5 Multiplexer Configuration 67
- X723-300151 5-2 Issue 2 68
- 5.1.5 Configuration Menu 69
- 5.2 Time Menu 70
- X723-300151 5-5 Issue 2 71
- X723-300151 5-6 Issue 2 72
- 5.3 System Mode Menu 73
- X723-300151 5-8 Issue 2 74
- X723-300151 5-9 Issue 2 75
- X723-300151 5-10 Issue 2 76
- X723-300151 5-11 Issue 2 77
- X723-300151 5-12 Issue 2 78
- 5.4 Configuration Menu 79
- X723-300151 5-14 Issue 2 80
- X723-300151 5-15 Issue 2 81
- X723-300151 5-16 Issue 2 82
- X723-300151 5-17 Issue 2 83
- X723-300151 5-18 Issue 2 84
- X723-300151 5-19 Issue 2 85
- X723-300151 5-20 Issue 2 86
- X723-300151 5-21 Issue 2 87
- 5.4.5.1 Alarm Events 88
- X723-300151 5-23 Issue 2 89
- 5.4.5.2 Route Alarms 90
- 5.4.5.3 External Relays 90
- 5.4.5.4 Card Out 91
- X723-300151 5-26 Issue 2 92
- X723-300151 5-27 Issue 2 93
- X723-300151 5-28 Issue 2 94
- X723-300151 5-29 Issue 2 95
- X723-300151 5-30 Issue 2 96
- X723-300151 5-31 Issue 2 97
- X723-300151 5-32 Issue 2 98
- X723-300151 5-33 Issue 2 99
- X723-300151 5-34 Issue 2 100
- X723-300151 5-35 Issue 2 101
- X723-300151 5-36 Issue 2 102
- X723-300151 5-37 Issue 2 103
- X723-300151 5-38 Issue 2 104
- X723-300151 5-39 Issue 2 105
- 5.5 Remote Menu 106
- 5.6 Smart Menu 107
- X723-300151 5-42 Issue 2 108
- 6 Fault Reporting & 109
- Maintenance Facilities 109
- X723-300151 6-2 Issue 2 110
- X723-300151 6-3 Issue 2 111
- X723-300151 6-4 Issue 2 112
- X723-300151 6-8 Issue 2 116
- X723-300151 6-9 Issue 2 117
- X723-300151 6-10 Issue 2 118
- Maintenance Menu 119
- X723-300151 6-12 Issue 2 120
- X723-300151 6-13 Issue 2 121
- X723-300151 6-14 Issue 2 122
- X723-300151 6-15 Issue 2 123
- X723-300151 6-16 Issue 2 124
- X723-300151 6-18 Issue 2 126
- X723-300151 6-19 Issue 2 127
- 6.3 Network Problems 128
- 6.4 Built-in Test Facilities 129
- X723-300151 6-22 Issue 2 130
- 6.5 NCS Fault Levels 131
- X723-300151 6-24 Issue 2 132
- X723-300151 6-25 Issue 2 133
- X723-300151 6-26 Issue 2 134
- X723-300151 6-27 Issue 2 135
- X723-300151 6-28 Issue 2 136
- X723-300151 6-29 Issue 2 137
- X723-300151 6-30 Issue 2 138
- 7 Channel Interface Cards 139
- X723-300151 7-2 Issue 2 140
- 7.2 Approvals 141
- X723-300151 7-4 Issue 2 142
- 8 3000 Power Supply Equipment 143
- X723-300151 8-2 Issue 2 144
- 8.3 Specifications 145
- X723-300151 8-4 Issue 2 146
- 8.4 Power Wiring 147
- X723-300151 8-6 Issue 2 148
- 8.5 Commissioning 149
- 8.6 Maintenance 150
- THE MAINS LEAD DISCONNECTED 150
- A Patchfield Electrical 151
- Diagrams 151
- Patchfield No. 1 152
- Patchfield No. 2 152
- Patchfield No. 3 153
- Patchfield No. 4 153
- Patchfield No. 5 154
- Patchfield No. 6 154
- Patchfield No.7 155
- X723-300151 A-6 Issue 2 156
Verwandte Produkte und Handbücher für Vernetzung Case Communications 3200
Lippert-components CA-CGL manuály
Uživatelské manuály a uživatelské příručky pro Hardware Lippert-components CA-CGL.
Poskytujeme 1 manuály pdf Lippert-components CA-CGL ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Lippert components CA-CGL Uživatelský manuál (2 strany)
Značka: Lippert-components | Kategorie: Hardware | Velikost: 0.14 MB |
Tabulka s obsahem
Další produkty a příručky pro Hardware Lippert-components
| Modely | Typ Dokumentu |
|---|---|
| CA-FD7 |
Uživatelský manuál
Lippert Components CA-FD7 User Manual,
2 stránky
|
| CA-FU |
Uživatelský manuál
Lippert Components CA-FU User Manual [de] [fr] [it] ,
1 stránky
|
| CA-MT |
Uživatelský manuál
Lippert Components CA-MT User Manual [en] [de] ,
1 stránky
|
| CA-UR |
Uživatelský manuál
Lippert Components CA-UR User Manual,
1 stránky
|
| Ground Control 2.0 |
Uživatelský manuál
Lippert Components Ground Control 2.0 User Manual,
12 stránky
|
| Ground Control 2.0 |
Uživatelský manuál
Lippert Components Ground Control 2.0 User Manual [en] [de] [es] [it] ,
10 stránky
|
| Ground Control 3.0 |
Uživatelský manuál
Lippert Components Ground Control 3.0 User Manual [en] ,
19 stránky
|
| Ground Control 3.0 Aftermarket |
Uživatelský manuál
Lippert Components Ground Control 3.0 Aftermarket User Manual [de] [fr] [it] ,
20 stránky
|
| Ground Control 3.0 OEM |
Uživatelský manuál
Lippert Components Ground Control 3.0 OEM User Manual,
15 stránky
|
| Ground Control 3.0 |
Uživatelský manuál
Lippert Components Ground Control 3.0 User Manual,
26 stránky
|
| Ground Control 3.0 |
Uživatelský manuál
Lippert Components Ground Control 3.0 User Manual,
13 stránky
|
| LCI’s Motor Home Electronic Controlled Hydraulic L |
Uživatelský manuál
Lippert Components LCI’s Motor Home Electronic Controlled Hydraulic Leveling System Automatic Controls Addendum User Manual,
4 stránky
|
| LCI Motorized Leveling (2009 - Present) |
Uživatelský manuál
Lippert Components LCI Motorized Leveling (2009 - Present) User Manual,
19 stránky
|
| LCI Electronic/Hydraulic Leveling & Slideout |
Uživatelský manuál
Lippert Components LCI Electronic/Hydraulic Leveling & Slideout User Manual [en] ,
31 stránky
|
| Ultra Level |
Uživatelský manuál
Lippert Components Ultra Level User Manual [cs] [en] [pl] [de] ,
12 stránky
|
| LCI Level-Up Motorhome Leveling (2013-present) |
Uživatelský manuál
Lippert Components LCI Level-Up Motorhome Leveling (2013-present) User Manual [en] ,
20 stránky
|
| Level-Up Motorhome Leveling |
Uživatelský manuál
Lippert Components Level-Up Motorhome Leveling User Manual [cs] [it] [de] [en] ,
10 stránky
|
| Level Up |
Uživatelský manuál
Lippert Components Level Up User Manual [pl] [en] [de] ,
10 stránky
|
| 5th Wheel Hydraulic Slideout And Landing Gear (hlg |
Uživatelský manuál
Lippert Components 5th Wheel Hydraulic Slideout And Landing Gear (hlg) System User Manual [fr] [de] ,
31 stránky
|
| Hydraulic Landing Gear - 14k Aluminum |
Uživatelský manuál
Lippert Components Hydraulic Landing Gear - 14k Aluminum User Manual,
4 stránky
|
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.030 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern